MASTERPAV EC13
SF Epoxy Coating
MASTERPAV EC13 SF is a two-component, solvent-free epoxy coating formulated for medium to heavy-duty industrial flooring. With its low-viscosity pigmented composition, EC13 is designed to be used as a topcoat over primed concrete surfaces, offering a durable, seamless, and chemical-resistant finish.
When combined with non-slip aggregates, EC13 can be applied to create textured, anti-slip flooring suitable for safety-critical environments such as factories, processing areas, or warehouses. It is ideal for interior concrete surfaces requiring long-term resistance to mechanical and chemical wear.
BENEFITS
- Solvent-free formula for safer, high-performance indoor use
- Medium to heavy-duty durability for high traffic areas
- Compatible with anti-slip aggregates for textured surfaces
- Seamless, hygienic, and pigmented finish
- High resistance to abrasion and chemical exposure
- Easy to clean and maintain
RECOMMENDED APPLICATION
- Exhibition hall & showroom
- Hotel Lobbies & entryways
- Residential & commercial floor
- Offices
- Restaurants
- Garage floors
PRODUCT INFORMATION
THEORITICAL COVERAGE
2.5 kg/m2
PACKAGING
Available in 4 & 20kg set
4kg set (3kg Part A: 1kg Part B) + 100g MASTERPAV Metallic (approx. 1.6m2)
20kg set (15kg Part A: 5kg Part B) + 500g MASTERPAV Metallic (approx. 8m2)
INSTRUCTION FOR USE
- Prepared Concrete Substrate
- 0.3 kg/m2 MASTERPAV EC 10
- 2.5 kg/m2 MASTERPAV EC 19
SURFACE PREPARATION
· The concrete surface to receive the MASTERPAV EC19 Metallic Epoxy Coating shall be subjected to mechanical grinding to achieve a concrete surface profile (CSP) 1 – 3 as recommended by ICRI.
· The concrete surface shall be thoroughly clean and free from any debris or dust by subjecting to high-pressure cleaning or vacuum machine.
· It is recommended to conduct concrete moisture test before application of MASTERPAV EC19 Metallic Epoxy Coating. Concrete substrate shall have moisture content of maximum 4%. For concrete substrate with moisture content higher than 4%, a moisture barrier is recommended.
· All cracks are to be rectify before actual application.
PRIMER
· Pour the entire content of Part B into Part A of MASTERPAV EC10.
· Mechanically mix the mixture using low power mixer until homogeneous.
· Apply the mixed material using suitable roller and allow it to dry overnight.
TOPCOAT
· The previously applied primer should be cured, dry to the touch, and no longer tacky.
· Light sanding the surface (promotes good bond between coats), follows by vacuuming.
· Wipe clean the dust using a microfiber wipe with a suitable solvent (eg: MASTERPAV Thinner 101)
· Pour the entire content of Part B into Part A of MASTERPAV EC19 Metallic Epoxy Coating.
· Mechanically mix the mixture using low power mixer until homogeneous.
· Divide the mixed epoxy into 2 cups and add color to each one (Cup 1: Base color, Cup 2: Highlight color). Cup 1 should be the main base color and have most of the epoxy, while Cup 2 should be your highlight color and have less epoxy.
· For every 4kg (A+B) epoxy resin, 1 pack of MASTERPAV Metallic pigments (100g) is recommended.
· Pour out the main base color which have most of the epoxy and spread it using 5mm notched floor squeegee.
· Use microfiber roller (deshedded) to blend the base and highlight epoxy to customize the design.
· The floor will keep self-leveling for hours. Allow the floor to cure 24 hours before you allow anyone step on it. (Pro tips: Spray 91% isopropyl alcohol 15 minutes after application to get rid of air bubbles in the epoxy surface)
· The MASTERPAV EC19 Metallic Epoxy Coating need 2.5kg for every m2 of the project.
CAUTION! DO NOT LEAVE MIXED PRODUCT IN A BUCKET. THIS WILL CAUSE A FASTER CHEMICAL REACTION & THE EPOXY WILL THICKEN FASTER THAN IT SHOULD. THIS WILL COMPROMISE THE WORKING TIME. REFER TO POT LIFE DATA BEFORE USE.
Color Chart

MISTY GREY

EX-GREY

BUTTERMILK

BRIGHT BLUE

FRESH BLUE

WHITE

DARK GREEN

EVERGREEN